Guide

THE TOOLBOX / HOME & PLUMBING

Sump Pump Size Calculator —
GPH Capacity, Total Dynamic Head & Horsepower Matcher.

Calculate your exact Total Dynamic Head (vertical lift + PVC pipe friction) and sump pit inflow rate so you pick the right 1/3 HP, 1/2 HP, or 3/4 HP pump without short-cycling.

Preset:

1. Discharge Pipe & Lift Geometry

8 ft
15 ft

2. Sump Basin Inflow Rate Test

Time how long water takes to rise in your sump basin during heavy rain (pump unplugged briefly):

Recommended HP
1/3 HP
Submersible cast iron
Total Head (TDH)
11.6 ft
8ft lift + 3.6ft loss
Target Flow
1,200
GPH @ 12ft head
8ft15ft RUN · 1.5" PVC · TDH 11.6ft
Sizing & Backup Guidance

Ideal for standard residential basements with moderate seepage and ≤ 10 ft head.

Measured basin inflow: 2.2 GPM (132 GPH). Always check the pump box's flow curve at 12 ft head—not the marketing “0 ft head” rating—and add a battery or water-powered backup pump if you have a finished basement.

SUMP PUMP HORSEPOWER GUIDE

Typical Residential Sump Pump Flow Capacity at 10 ft Head.

HorsepowerTypical Flow @ 10 ft HeadBest Basement Application
1/3 HP2,000 – 2,600 GPHAverage home, 7–9 ft lift, light to moderate rainwater
1/2 HP3,000 – 4,200 GPHHigh water table, 10–14 ft lift, finished basements
3/4 HP – 1 HP4,500 – 6,000+ GPHDeep pits, long runs, flood-prone or commercial drainage

2. Dual-Pump Redundancy

Most basement floods happen during summer thunderstorms when utility power fails. Pair your primary AC pump with a 12V deep-cycle battery backup or municipal water-powered backup pump.

Frequently Asked Questions

What horsepower sump pump do I need for an average basement?

A 1/3 HP cast-iron submersible sump pump handles most average-sized residential basements with an 8-foot vertical lift and moderate rainwater seepage. Step up to a 1/2 HP pump if your vertical lift exceeds 10 feet, your horizontal discharge run is over 25 feet, or your pit fills rapidly during storms.

What is Total Dynamic Head (TDH) on a sump pump?

Total Dynamic Head is the vertical height the pump must lift water (static head) plus the equivalent friction resistance from pipe length, 90° elbows, and the check valve. Always read a pump’s GPH performance chart at your actual TDH (typically 10 ft)—never at 0 ft head.

How do I measure my sump pit inflow rate in GPH?

During a wet spell, unplug the pump briefly, measure how many inches the water level rises over a timed interval (e.g., 6 inches in 3 minutes), and enter your pit diameter (usually 18 inches). Our calculator converts that cylinder volume into GPM and GPH and adds a 1.5× storm safety margin.

Should I buy a 1/2 HP or 3/4 HP sump pump just to be safe?

Going from 1/3 HP to 1/2 HP is often a smart upgrade for high-water-table homes, but massively oversizing (e.g., putting a 1 HP pump in a small slow-filling pit) causes rapid "short-cycling" on and off, which wears out float switches and motors prematurely.

What size discharge pipe should a sump pump use?

Use 1.5-inch Schedule 40 PVC for almost all 1/3 HP and 1/2 HP residential sump pumps. Shrinking down to 1.25-inch pipe more than doubles friction head loss and chokes flow rate.

Do I need a check valve on my sump pump discharge line?

Yes. A silent spring-loaded check valve installed just above the pit prevents the vertical column of water in the pipe from rushing back into the basin when the pump shuts off—eliminating water hammer and short-cycling.