Guide

HOME & ENERGY CALCULATORS · DOE FHR & TANKLESS GPM

Water Heater Size Calculator,
tank FHR vs. tankless GPM.

Calculate exact storage tank First Hour Rating (FHR) and tankless water heater GPM, temperature rise (ΔT), gas BTU/h, and electric kW/amps using U.S. DOE fixture formulas.

Household Presets
1. Groundwater Climate & Temperature RiseΔT = 68°F
2. Peak-Hour Uses (Tank FHR Worksheet)66 gal / hr
Showers
10 gal each
3
Bathtub Fills
15 gal each
1
Dishwasher
6 gal / cycle
1
Clothes Washer
7 gal / load
1
Hand Dishes
4 gal / session
0
Sink / Shaving
2 gal each
4
3. Running at the Exact Same Time (Tankless GPM)6.5 GPM
Standard Shower
2.0 GPM
2
Low-Flow Shower
1.5 GPM
0
Bathtub Spout
4.0 GPM
0
Kitchen Sink
1.5 GPM
1
Bathroom Faucet
1.0 GPM
1
Dishwasher
1.5 GPM
0
Washing Machine
2.0 GPM
0
Storage Tank Target
≥ 70 FHR
Peak-hour draw: 66 gal. Look for an EnergyGuide First Hour Rating at or above 70 gal.
Tankless Target
6.5 GPM
At 68°F rise (52°F → 120°F). Needs ~246k BTU/h gas.
Water Heater TypeRecommended Size / SpecBest For
Gas Storage Tank50-gal (FHR ≥ 70)Fast recovery, lower upfront install
Electric Storage Tank65-gal (FHR ≥ 70)Homes without natural gas lines
Heat Pump Hybrid65-gal (FHR ≥ 70)Lowest annual electric bill (~3× efficiency)
Gas Tankless (Condensing)245,556 BTU/h @ 6.5 GPMEndless hot water, compact wall mount
Electric Tankless65.4 kW (273A @ 240V)Warm climates or point-of-use only
Sizing Recommendation: Peak load (245,556 BTU/h) exceeds a single 199k BTU/h tankless unit—consider two cascaded units or a high-FHR tank.

Error: Sized for 66 gal peak-hour FHR and 6.5 GPM simultaneous flow at 68°F rise.

Based on U.S. DOE First Hour Rating & GPM thermal formulas

SIZING FORMULAS

Comparing First Hour Rating (FHR) against Tankless GPM & BTU.

1. DOE First Hour Rating (Tank)

Add up hot-water uses during your single busiest hour of the day (typically morning showers + dishwasher). Pick a tank whose EnergyGuide FHR equals or exceeds that gallon total.

2. Tankless Flow Rate & ΔT

Tankless units are rated by flow rate at a specific temperature rise. Always check the manufacturer’s GPM chart at your winter groundwater temperature, not summer.

3. Heat Pump Hybrid Advantage

If you are sizing an all-electric home, a 65- or 80-gallon heat pump water heater runs on a standard 30A/240V circuit while using ~65%–70% less electricity than a resistive tank.

Frequently Asked Questions

What is First Hour Rating (FHR) on a storage tank water heater?

First Hour Rating (FHR) is the U.S. Department of Energy metric printed on the yellow EnergyGuide label that tells you how many gallons of hot water a fully heated tank can supply during its busiest hour, combining stored tank volume and burner/element recovery rate.

How do I size a tankless water heater in GPM and BTU?

Add the flow rates (GPM) of every fixture you run simultaneously—such as two 2.0 GPM showers plus a 1.5 GPM sink (5.5 GPM)—then subtract your winter groundwater temperature from your 120°F target to get Temperature Rise (ΔT). Required gas input is roughly GPM × ΔT × 500 ÷ efficiency.

Why does groundwater temperature matter so much for tankless sizing?

In northern states where winter groundwater enters at 40°F–45°F, a tankless heater must lift water by 75°F–80°F to reach 120°F, cutting its maximum GPM output nearly in half compared to Florida or Texas where inlet water is 68°F–72°F.

Can my 200-amp electrical panel run a whole-house electric tankless water heater?

Often not in cold climates. Heating 5.0 GPM across a 70°F rise requires ~51 kW (over 210 Amps at 240V), which exceeds a standard 200A home service. In those cases, a 65–80 gallon Heat Pump Hybrid tank or a condensing Gas Tankless unit is a much better fit.

Should I choose a 40-gallon, 50-gallon, or 65-gallon tank?

Match your tank’s FHR rather than tank gallons alone: 40-gallon gas tanks typically deliver 55–65 FHR (1–3 people), 50-gallon gas or hybrid tanks deliver 65–85 FHR (3–4 people), and 65–80 gallon tanks handle 5+ residents or soaking tubs.