Guide

THE TOOLBOX / CARPENTRY & WOODWORKING

Miter Angle Calculator —
Crown Molding Compound Miter, Bevel & Baseboard Saw Settings.

Calculate exact miter and bevel saw angles for flat-cut crown molding, upside-down nested crown, baseboards, bay windows, and out-of-square corners—with piece-by-piece fence orientation guides.

Wall Angles:
Wall: 90° (inside)Left PieceRight Piece
Exact Miter Saw Dial SettingsJoint Bisector: 45.0°
Miter Angle (Table)
31.62°
Nearest ½°: 31.5°
Bevel Angle (Tilt)
33.86°
For 38° spring angle
Left Wall Piece

Top edge against fence · Miter RIGHT 31.62° · Bevel LEFT 33.86° (keep left side)

Right Wall Piece

Bottom edge against fence · Miter LEFT 31.62° · Bevel LEFT 33.86° (keep right side)

Common Corner Cheat Sheet (38° Spring Angle)

Wall CornerBaseboard / NestedFlat MiterFlat Bevel
88°46.00°32.52°34.53°
89°45.50°32.07°34.20°
90°45.00°31.62°33.86°
91°44.50°31.17°33.53°
92°44.00°30.73°33.19°
120°30.00°19.57°23.20°
135°22.50°14.31°17.55°

COMPOUND MITER SAW REFERENCE

Standard Crown Molding Flat-Cut Settings (90° & 135° Corners).

Spring Angle90° Corner Miter / Bevel135° Bay Window Miter / Bevel
38° (52/38 Standard)31.62° Miter / 33.85° Bevel14.31° Miter / 17.56° Bevel
45° (45/45 Colonial)35.26° Miter / 30.00° Bevel16.32° Miter / 15.70° Bevel
52° (38/52 Steep)38.24° Miter / 25.81° Bevel18.08° Miter / 13.63° Bevel

1. Compound Miter Trigonometry Formulas

For crown molding laid flat on the saw bed with spring angle S and measured wall corner W: Miter = atan(sin(S) ÷ tan(W ÷ 2)) and Bevel = asin(cos(S) × cos(W ÷ 2)). For baseboards or nested crown, Miter = 90° − (W ÷ 2).

2. Pro Tip: Always Cut Test Scraps First

Drywall tape and corner bead routinely push nominal 90° corners to 88.5° or 91.5°. Cut two 6-inch scrap pieces at your calculated angles and dry-fit them in the corner before cutting full 12-foot sticks.

4. Works Offline in the Workshop

All trigonometric calculations execute instantly on your phone or tablet browser with zero server round-trips.

Frequently Asked Questions

What are the miter and bevel angles for 90° crown molding cut flat?

For standard 38° spring-angle crown molding (52°/38°) on a 90° corner laid flat on the saw bed, set your miter angle to 31.62° and your bevel tilt to 33.85°. For 45°/45° crown molding on a 90° corner, set miter to 35.26° and bevel to 30.00°.

How do I calculate a miter angle for an out-of-square wall?

Measure the actual corner angle with a digital angle finder (for example, 91.5°). For baseboard or nested crown molding, the miter setting is 90° − (Wall Angle ÷ 2), which equals 44.25°. For flat-cut compound crown molding, enter the exact wall angle and spring angle above to compute both the compound miter and bevel.

What is the difference between cutting crown molding flat vs. nested upside-down?

Cutting nested (upside-down against the fence at its installed spring angle) only requires a simple miter cut (45° for a 90° corner) with 0° bevel, but large 5"–7" crown moldings often exceed the saw’s vertical fence height. Cutting flat on the saw table works on any width of crown molding using compound miter + bevel angles.

How do I know if my crown molding has a 38° or 45° spring angle?

Most modern builder-grade and colonial crown moldings sold at hardware stores have a 38° spring angle (52° wall angle / 38° ceiling angle). Symmetrical profiles where the top and bottom flat backs are identical have a 45° spring angle. Check the manufacturer’s label or hold a piece against a 90° corner and measure its wall angle.