Guide

Life

Truck Tire Load Calculator

Dial in the exact cold PSI for pickup trucks, SUVs, towing rigs, and P-Metric to LT (Load Range C/D/E) tire upgrades using TRA load-inflation math.

Truck Setups:

Tire Rating & Axle Weights

Recommended Cold Tire Pressures

Front Axle (2 Tires)
35 PSI
Load: 1,900 lbs/tire · Axle Capacity: 4,211 lbs
Rear Axle (2 Tires)
48 PSI
Load: 2,300 lbs/tire · Axle Capacity: 5,066 lbs
Sidewalk Chalk-Test Fine-Tuning

Draw a thick sidewalk-chalk stripe across the tread and roll straight 20 feet on dry pavement:

  • Center wears off first: Over-inflated for empty driving → drop 2–3 PSI (stay above minimum load PSI).
  • Outer shoulders wear off first: Under-inflated → add 2–3 PSI to prevent sidewall heat buildup.
  • Even wear edge-to-edge: Optimal contact patch for ride comfort and tread life.

Understanding Truck Tire Load Ranges & Cold PSI

Tire air pressure—not rubber ply count alone—is what actually carries your truck's weight. Using this truck tire load calculator helps you avoid the two most common pickup mistakes: under-inflating heavy LT tires (causing dangerous sidewall flexing and blowouts) or blindly airing Load Range E tires to 80 PSI on an empty bed (causing center-tread wear and bone-jarring rides).

Tire DesignationPly RatingMax Load PSITypical Vehicle Use
P-Metric SL4-Ply35 PSIFactory half-ton pickups, crossovers, daily SUVs
P-Metric XL4-Ply Reinforced41–42 PSIFull-size SUVs, heavy EVs, light towing half-tons
LT Load Range C6-Ply50 PSIMidsize 4×4s (Tacoma, Wrangler, Bronco) & trail rigs
LT Load Range D8-Ply65 PSIHalf-ton work trucks & overland builds
LT Load Range E10-Ply80 PSI3/4-ton & 1-ton HD trucks, fifth-wheel & gooseneck towing

Frequently Asked Questions

Why do LT Load Range E tires need different PSI than my truck’s door-jamb sticker?

If your half-ton pickup came from the factory with P-Metric (SL) tires rated at 35 PSI, switching to 10-ply LT Load Range E tires changes the load-inflation curve. Under Tire and Rim Association (TRA) standards, LT tires typically need higher cold PSI (often 42–50 PSI) to match the same carrying capacity—yet running them at their 80 PSI sidewall max while unloaded creates a harsh ride and wears out the center tread.

What is the 1.10 P-Metric derating rule on trucks and SUVs?

When passenger-car (P-Metric) tires are installed on light trucks, vans, or SUVs, the Tire and Rim Association requires dividing their sidewall load capacity by 1.10 to account for higher centers of gravity and heavier duty cycles. Our calculator automatically applies this 1.10 factor whenever P-Metric tires are selected.

Should I inflate my Load Range E tires to 80 PSI when towing?

Only if your actual rear axle weight requires 80 PSI. Weigh your loaded truck and trailer at a CAT scale first, enter the front and rear axle weights, and inflate each axle to match its real load plus a 10% safety buffer. Inflating higher than needed sacrifices wet traction and comfort.

How does Dual Rear Wheel (DRW / Dually) tire capacity differ from single rear wheels?

Because dual tires share heat and uneven road crowns, TRA load tables reduce each tire’s individual maximum rating by roughly 9% compared to single-wheel use—while doubling the number of tires on the rear axle from 2 to 4.

What is the sidewalk chalk test for truck tires?

After calculating your safe minimum load PSI, draw a wide chalk line across the tread of each tire and drive straight on flat, dry pavement for 20 feet. If the chalk rubs off only in the center, pressure is slightly too high; if only the outer edges wear off, add 2–3 PSI until the chalk clears evenly.

When should I measure tire pressure?

Always measure and set PSI when tires are cold—ideally first thing in the morning before driving more than one mile, and out of direct midday sunlight. Highway driving raises internal tire pressure by 4 to 8 PSI, which is normal and should never be bled down hot.